Miura Panel Workbench three.js r128 · relief to STL

Tileable wall panels in the Miura-ori fold, as solid reliefs with a flat back. Hang a few on the preview wall, graze them with a strip light from below or above, and download the one you like as an STL.

Starting…

Things to try

  • Turn the chevrons. Lit from below, chevrons pointing up or down band the wall in horizontal stripes, light facets facing down and dark ones facing up. Point them left or right and the light runs along the ridges instead, so each arm of a chevron lights against its neighbour and the herringbone shows.
  • Bring the strip in. At 10 to 20 mm off the wall the light only catches the facets that face it, and the gradient up a tall wall gets steep. Further out it flattens and the shadows shorten.
  • Gap. At 0 mm with no frame the relief runs straight across the joins. Grazing light shows any step between panels, so mount them on a flat batten or cleat.
  • Front. Lit flat from the front, the same panel nearly disappears. Most of what you see comes from the angle of the light.

Drag to rotate, scroll or pinch to zoom, double-click to reset. Keys: L cycle the light, B back view, D download, P download a keyhole plate, 0 reset view, F full screen.

Printing

  • Back down, no supports. The STL is binary, in millimetres, with the flat back on Z = 0 and Y running up the wall. Every facet faces up, so nothing overhangs.
  • Terraces. Each facet is a sloping top surface, so the layers show as steps. The readout gives their width at 0.2 mm layers. Variable layer height in the slicer shrinks them a lot, and filler primer, a sand, and a spray hides the rest. Under grazing light, missed steps show up as hatching.
  • Infill. 10 to 15% is plenty. The back plate only has to stay flat, so three or four bottom layers are worth more than the infill.
  • Keyholes. Each is a T-section pocket: a narrow neck at the back, a wider chamber for the screw head above it, and a roof that bridges about the width of the head, so it still prints without supports. It is about 5 mm deep, and the front dips to the back thickness in every valley, so keyholes usually want a back of 6 mm or more. The readout says how much plastic covers the roof, and the download refuses a panel where it would go right through.
  • Plates. The other way: the keyholes go in small blocks, printed separately (one STL, print as many as there are keyholes) and glued into shallow recesses in a thin panel. Each plate has its own 1.2 mm roof, so glue can't foul the slot. The panel stands off the wall by the plate thickness less the recess, which the preview shows; under grazing light that gap reads as a shadow line round the panel. Print plates pocket side down, like the panel.
  • Hanging. Pan-head or button-head screws suit the chamber best. Set one, hang the panel, level it, and mark the second through the head hole before taking it down. Keep the strip light off the panel itself; PLA creeps at about 55 °C.

Geometry

The front is Miura-ori as a height field: a zigzag pleat in Y, sheared sideways by a zigzag in X. Every facet is a flat parallelogram, so a sheet could fold to the same shape.

vertex(i, j) = ( i·w,
                 j·h + (i odd ? w·tan α : 0),
                 base + (j odd ? depth : 0) )

One repeat is 2w across and 2h up, and a panel is a whole number of them, so the relief cut at one edge matches the opposite edge. Each facet is clipped to the panel rectangle, shared points are welded, and walls drop from the rim to a flat back, triangulated by ear clipping round any keyhole necks. The result is a closed solid with no T-junctions.

The readout's sector angle is the corner of each parallelogram before folding, for comparison with a paper fold.